This unique adhesive is free from solvents, isocyanates, and other hazardous raw materials. It cures on exposure to atmospheric moisture to form a strong durable bond between two surfaces. Due to its unique properties, it also remains a highly durable flexible seal. It has been formulated to offer outstanding primer-less adhesion to most materials, especially various types of plastics and including other materials such as vinyl, aluminum, steel, concrete, wood, and glass.

A test placement prior to general use is always recommended. Step 1 - Cut the tip off of the cartridge; screw onto the nozzle, and insert into the caulk gun. Be sure to pierce the membrane at the front of the tube before applying pressure.

Proto Corporation can supply manual caulk guns that feature a superior Press evenly on the caulk gun for the length of the part so the adhesive is distributed equally. Allowing the adhesive to seep out slightly from the edge of the overlap is desired and creates a good seal.

Can non-dilutable stock (or equivalent) be issued? - Equity, Legal

Step 3 - Using a clean putty knife, scrape off any excess adhesive along the seam. Step 4 - Finally, wipe off the area with a clean rag and mineral spirits to finish off the job. Cleanup must be performed before the adhesive has time to set up. If all the contents in the tube are not used, simply allow a small amount of caulk to dry at the tip of the applicator to form a plug and remove when ready to use again.

Shelf life for ProtoOne is approximately one year from the date of manufacture. Tooling time allows for about three to five minutes before ProtoOne starts to form a skin and set in, however factors including ambient temperature and humidity can affect this. Additionally, a water misting spray should be used on the caulk bead to accelerate the activation time when applying ProtoOne in low humidity and dry climate environments.

Proto Corporation recommends a minimum of twenty-four hours before removing any tape so the adhesive has time set up and create a seal. Optimum strength is achieved in seven days. In countries where high heat and humidity are a factor, special precautions must be taken. Store product in a covered, well-ventilated warehouse and avoid excessive heat conditions.

Rotation of stock is an absolute necessity.

Cartons should always be stacked upright with the nozzle tip pointed upwards. DO NOT store within 1 meter of the roofline of the warehouse or storage building. It is supplied in cartons of 12 each.

DIRECT CONTACT OF UNCURED ADHESIVE IRRITATES EYES AND MAY IRRITATE SKIN. Avoid eye and skin contact. Use with adequate ventilation. Do not handle contact lenses with sealant on hands.

IN CASE OF EYE CONTACT, flush eyes with water for 15 minutes.

Form K

IN CASE OF SKIN CONTACT, remove from skin and flush with water. KEEP OUT OF THE REACH OF CHILDREN. The information and data contained herein is believed to be accurate and reliable; however, it is the user's responsibility to determine suitability of use. Since the supplier cannot know all the uses, or the conditions of use to which these products may be exposed, no warranties concerning the fitness or suitability for a particular use or purpose are made.

It is the user's responsibility to thoroughly test any proposed use of our products and independently conclude satisfactory performance in the application.

Likewise, if the application, product specifications or manner in which our products are used require government approval or clearance, it is the sole responsibility of the user to obtain authorization.

The supplier warrants only that its products will meet its specifications. There is no warranty of merchantability or vegan cashew cream cheese icing for use, nor any other express or implied warranty.

The user's exclusive remedy and the supplier's sole liability how to do the analysis for binary options limited to refund of the purchase price or replacement of any product shown to be otherwise than as warranted.

The supplier will not be liable for incidental or consequential damages of any kind. Moisture Curing Sealant Molecular Formula: Mixture Proper DOT Shipping: N-beta- aminoethyl -gamma-aminopropyltrimethoxysilane CAS Number: The HMIS rating involves data interpretation that varies from company to company.

This information is intended for general identification to specific hazards. To safely handle this material, all of the information in this MSDS should be considered. Primary Routes of Entry: Inhalation of vapor may irritate the respiratory tract and nasal passage. Prolonged inhalation of vapors may cause adverse effects on the central nervous system, including dizziness, nausea, and vomiting.

Trading stocks and options with moving averages single short exposure may cause irritation.

Repeated prolonged exposure may cause mild irritation. Direct contact non dilutable stock options slightly with redness and swelling. There are no taxability of restricted stock options symptoms of ingestion. Immediately flush eyes with copious amounts of water. Wash skin with soap and water. Get medical attention if irritation or ill effects develop or persist.

Remove subject to fresh air. Get medical attention if ill effects persist. If this product is oanda reviews forex peace army, call physician or poison non dilutable stock options center for most current information.

DO NOT INDUCE VOMITING, unless directed by medical personnel. Treat according symptoms and eliminate overexposure. On large fires use dry chemical, foam, or water spray. On small fires use carbon dioxide, dry trading stocks stop limit, or water spray. Water can be utilized to cool containers exposed forex trading sole 24 ore fire.

Unusual Fire and Explosion Hazards: When involved in a fire, this material may decompose and produce the following toxic gases: Contact with water will release small quantities of flammable methanol. Fire responders must wear self-contained breathing apparatus and full protective equipment.

Move fire-exposed containers if it can be done without risk to firefighters. If possible, control water run-off to prevent environmental contamination.

Observe all personal protective equipment recommendations as described in section eight. Scrape all spilled materials for disposal. This material is not classified as a hazardous waste per 40 CFR State and local laws may impose regulatory restrictions.

Avoid breathing vapors in top of shipping container. Avoid contact with skin and clothing. Wash thoroughly after handling. Observe all PPE suggestions in section 8. Keep container closed and store in a cool well-ventilated area. Avoid contact with water or moisture. Local and general ventilation is recommended.

Wear safety glasses with side shields as a minimum. Impervious gloves are suggested. Wash at mealtimes and end of shift. Dilutable in wet stage. Thermal decomposition products include carbon monoxide, carbon dioxide, nitrogen oxides, aldehydes, silicon dioxide, and various polymer compounds. Oxidizing acids, amines, strong caustics and water. Contact with incompatible materials and exposure to extreme temperatures.

Observe all federal, state, and local laws regarding waste disposal. All chemical substances found in this product comply with the Toxic Substances Control Act inventory reporting requirements. No components subject to 40 CFR None present or none present in regulated quantities. All ingredients are listed on the DSL.

Access to this page has been denied.

The opinions expressed herein are those of qualified experts within the company. We believe the information contained herein is current as of date of this MSDS. Since the use of the product is not within the control of company, the user's obligation to determine the conditions of safe use. STORAGE AND SHELF LIFE: Immediately clean any adhesive from unwanted areas using mineral spirits. Suggestions of uses should not be taken as inducements to infringe on any patent.

MATERIAL SAFETY DATA SHEET Product Name: Chemical Product and Company Identification Product Name: Proprietary, non-hazardous Percent by Weight: Proprietary, non-hazardous Percent by Weight 10 — 30 Name: Hazards Identification HMIS Hazard Rating: Health 1 Flammability 1 Reactivity 0 Note: First Aid Measures Primary Routes of Entry: Fire Fighting Measures Flash Point: Handling and Storage Personal Precautionary Measures: Exposure Controls and Personal Protection Ventilation: Physical and Chemical Properties Boiling Point: Stability and Reactivity Stability: Disposal Considerations This material is not classified as a hazardous waste per 40 CFR Transport Considerations Marine pollutant components: Proto offers the widest range of colors in the industry Choose from the following PVC color options to suit your needs.

Proto Corporation is a proud member of. Proto Corporation employs best environmental practices for a greener tomorrow.